For professional installers

Installing KLAR-NET

Everything needed to fit, wire and configure KLAR-NET in a BMW with iDrive 7, 8 or 8.5.

Professional installers only. KLAR-NET is not a plug-and-play product. Installation requires experience with BMW audio systems and automotive Ethernet.

Step by step

Fitting the hardware

Work through these in order. For the exact connector and factory-amp wiring for each BMW sound system, see the wiring diagrams.

  1. Location

    Mount KLAR-NET as close as possible to the RAM (trunk, left side) so the Ethernet and CAN communication stays reliable. Fix it securely.

  2. Power

    KLAR-NET is powered through the EuroLab Y-cable, which takes power from the RAM supply. The RAM circuit is already fused and KLAR-NET draws about 150–250 mA, so no additional fuse is required.

  3. Ethernet

    • Connect the Ethernet cable coming from the MGU to KLAR-NET's MGU connector.
    • Connect the adapter cable between the RAM's Ethernet port and KLAR-NET's RAM connector.

  4. Centre speaker

    Connect the centre speaker directly to KLAR-NET's C connector.

  5. MATCH / Helix amps with SCP

    Connect the amplifier's SCP port to KLAR-NET's UART connector with the included cable.

  6. Optical

    • Connect a TOSLINK cable from KLAR-NET's F output to the amplifier's optical input.
    • The second TOSLINK output R can be used for the rear channels.

  7. Configuration

    Once all cables are connected and KLAR-NET is securely mounted, start the engine to keep KLAR-NET powered. Connect a laptop to KLAR-NET's USB-C port and open the Configurator — see below.

Amplifier setup

Helix / MATCH setup

In DSP PC-Tool, set the remote model to DIRECTOR or CONDUCTOR in the Helix / MATCH setup, and choose the same Remote type in the Configurator's Amplifier tab. With the CONDUCTOR, Volume 1 must be the master volume with the default 60 dB range and 1 dB steps. KLAR-NET does not switch sound profiles for each mode: it switches the amp's input to match the mode, and changes the profile only while the car radio plays.

WhenAmp inputAmp profile
Mode 2The input set in Input · Mode 2 — normally the optical (TOSLINK) input.Not changed — the amp keeps its main profile.
Mode 3The input set in Input · Mode 3 — the amp's own Bluetooth / USB player.Not changed.
Car radio playingThe radio input — normally the hi-level inputs.The radio profile is loaded; when the radio stops, the profile that was in use before comes back.
  1. Main profile

    In DSP PC-Tool, tune your main sound profile for music and make it the profile the amp starts with. It is used in Mode 2 and Mode 3.

  2. Radio profile (optional)

    If the radio needs a different tuning (it comes in on the hi-level inputs), create a second profile for it. If not, you can use the main profile for the radio too.

  3. Configurator

    In the Amplifier tab set Input · Mode 2 → optical, Input · Mode 3 → the amp's Bluetooth / USB input and Radio → radio profile + radio input. Radio set to off means KLAR-NET leaves the amp alone when the radio plays. Radio level optionally sets the radio volume.

Software

The Configurator

The Configurator runs in a browser on a laptop connected to KLAR-NET's USB-C port. Keep the engine running while you work.

Top bar

These controls work on every tab.

ControlWhat it does
ConnectConnects to KLAR-NET over USB. The USB dot turns on when connected.
Read from boardLoads the settings currently stored in KLAR-NET into the Configurator.
Save to boardWrites the current settings to KLAR-NET.
Save to fileSaves the settings as a file on the laptop — a backup, or to reuse in another car.
Load from fileLoads settings from a saved file into the Configurator. Use Save to board to apply them.
Reboot boardRestarts KLAR-NET.

Tabs: Status · Setup · Amplifier · Levels · Events · Sniffer · Tools — each described below.

Status

A live view of the car, the audio stream and KLAR-NET. Use it to check the install — nothing on this page changes a setting.

ItemWhat it shows
Status lineConnection state, the detected car, the head unit and the connected amplifier (not connected · car · car radio · amp).
Buffer levelHow full KLAR-NET's audio buffer is. It should stay near the 4096 target, out of the red zones at both ends.
avg · error · ppm · min…maxBuffer statistics: average level, deviation from target, clock difference in ppm, and the lowest/highest level seen.
Car valuesLive values read from the car: volume, fader, balance, nav volume, warning vol, PDC vol, speed vol, mph, speed boost (volume increase with speed) and amp link (SCP connection to the Helix / MATCH amp). Turn the knob or change fader/balance in iDrive to see them move.
Signal routingWhich speakers and amplifiers are in use: front amp (TOSLINK in), rear amp (TOSLINK in), centre speaker (C amp). Colours show music, nav and phone audio. Click a speaker to play a test tone.
Last 120 secondsGraph of the buffer level and ppm over the last two minutes.
Stream lineWhether KLAR-NET receives the music stream from the Ethernet tap, how many channels, and whether a nav prompt is playing.
Audio level L / RLevel meter in dBFS. Bar = RMS, mark = peak (held 1 s).
frames/s · underrunsAudio frame rate and buffer underruns — should stay at 0 — plus the status of car sounds, the car and the head unit.

Setup

The main install settings. Set the Operating mode first, then Save to board.

Operating modeWhat it doesUse when
Mode 1KLAR-NET sets the volume.Any amp with an optical input and no remote volume control.
Mode 2Bit-perfect: the amplifier sets the volume through its remote (SCP) port.Helix / MATCH amp connected to the UART cable.
Mode 3The amp plays its own Bluetooth. The car's volume knob still sets the volume; all car sounds play on the centre speaker.The owner streams to the amp's Bluetooth.
AutoMode 2 while the car plays music, Mode 3 when it does not.Switches automatically between Mode 2 and Mode 3.
Rear optical (R)What it does
Rear channelsRear music with fader. Centre sounds play on the built-in amp.
Center channelCentre sounds on this output. Built-in amp off.
OffNothing on R. Centre sounds play on the built-in amp.
Nav / phone voiceWhat it does
CenterCentre speaker, at the car's nav / phone volume.
Front opticalMode 1 only. Nav is mixed into the music; the call plays on the front output.
BothMode 1 only. Front optical and centre speaker.

Nav and phone voice output decide where those voices are heard. Modes 2 and 3 always use the centre speaker.

Head unit / SpeedWhat it does
AutoDetects the iDrive generation from the car.
iDrive 7 / 8Cars up to 2023.
iDrive 8.5Cars from 2024.
mph / km/hSpeed unit shown in the car.
REM OUT controlWhat it does
With the carOn when the car is on, off after the off delay.
With KLAR-NETOn while KLAR-NET is awake. Also for cars without a status frame.
Off delayHow many seconds REM OUT stays on after the car switches off (With the car only).

Amplifier

KLAR-NET talks to a Helix / MATCH amplifier over its remote-control (SCP) port — volume, sound setups and inputs. Used in Modes 2, 3 and Auto. In Mode 3 the steering wheel controls the amp's Bluetooth: next = next track, hold next ½ s = play/pause, prev = previous track. The amp's name appears once it is connected.

Amp remoteWhat it does
Remote typeDirector or Conductor: must match the remote model set in DSP PC-Tool.
Without remoteKLAR-NET is the only remote on the amp.
With remoteThe Director or Conductor stays connected alongside KLAR-NET. With the Conductor, using the car's volume freezes the knob; press and hold it to wake it.
ProfileThe amp's sound profile in use; you can also change it here.
InputThe amp input in use; you can also change it here.
RadioThe profile and input used while the car radio plays (off = not handled).
Input · Mode 2 / Mode 3The amp input KLAR-NET selects when Mode 2 or Mode 3 is active.
Radio levelRadio volume when radio is selected.
Amplifier BluetoothWhat it does
ConnectConnects to the last paired phone.
PairMakes the amp visible for pairing a new phone.
DisconnectDisconnects the phone, keeps the pairing.
DropForgets the phone.
Previous · Play/pause · NextTrack control. Works while Mode 3 is live.

Levels

Volume of each car sound and voice. Changes apply immediately and are stored after half a second. The left column sets levels for Modes 1 and 2, the right column for Mode 3 (amp on Bluetooth). With Play the sound when I release a slider ticked, the sound plays at the new level; the ▶ button next to a slider plays it too.

SliderWhat it sets
WarningsWarning chimes (seat belt, doors, alerts).
Radar 1First-stage driver-assist pre-warning (forward distance / active cruise), on the centre speaker.
Radar 2Frontal-collision warning — the urgent one. Briefly ducks the music and plays on the front optical in Modes 1 and 2, on the centre speaker in Mode 3.
Duck music for Radar 2How much the music is lowered while a Radar 2 warning plays.
PDCParking sensor beeps.
Click · Turn signaliDrive click and turn-signal tick.
Nav (center) · Phone (center)Nav and phone voices on the centre speaker.
Nav (front) · Phone (front)Nav and phone voices on the front optical output.

Test sounds play a car sound so you can check its level: warn1–warn4 are the four factory warning gongs (all follow the single Warnings slider), plus airbag, PDC front and PDC rear.

Events

Which sound plays for which car event. Drag a sound from the Sounds list onto an event, or click an event and then a sound. ▶ plays the event on the board; ↺ resets it to default. Empty slots (15 and up) fill from the Sniffer when a new car event is found; ✕ clears a slot.

Default events: Click, Radar 1, Radar 2, Warning 1–4 (Gong 1–4), Airbag / belt, Lane departure (Gong 4), Turn signal (Turn tick), PDC front beep, PDC front tone, PDC rear beep, PDC rear tone. The built-in sounds are always on the board; a loaded pack (KLAR-NET_SOUNDS_xxx.ksp) adds its own below them — choose the file, press Load pack (~30 s, car sounds silent meanwhile), assign the sounds, then Save to board.

Sniffer

A service tool for EuroLab only; it stays locked for installers. If a car needs it, EuroLab support works on it remotely through TeamViewer on the installer's laptop.

Tools

Update firmware installs a newer KLAR-NET firmware from the Downloads page:

  1. Press Choose File and select the update file (KLAR-NET_FWxxx.enc).
  2. Press Start update. The update takes about a minute.
  3. Keep the USB cable connected and do not close the page until it says "Updated".

Settings on this tab is a reminder of the top-bar buttons (Read from board, Save to board, Save to file, Load from file, Reboot board) — they work on every tab.

Need the wiring for a specific system?

Per-system connector diagrams for HiFi, Harman Kardon and Bowers & Wilkins, plus the Y-cable and connector guide.

Open the wiring diagrams →